Kichler 49339 Manuel d'utilisateur télécharger pdf

1) TURN OFF POWER.

IMPORTANT: Before you start, NEVER attempt any work

without shutting off the electricity until the work is done.

a) Go to the main fuse, or circuit breaker, box in your

home. Place the main power switch in the “OFF”

position.

b) Unscrew the fuse(s), or switch “OFF” the circuit breaker

switch(s), that control the power to the ﬁxture or room that

you are working on.

c) Place the wall switch in the “OFF” position. If the ﬁxture

to be replaced has a switch or pull chain, place those in

the “OFF” position.

2) Find the appropriate threaded holes on mounting strap.

Assemble mounting screws into threaded holes.

3) Attach mounting strap to outlet box. (Screws not provided).

Mounting strap can be adjusted to suit position of ﬁxture.

4) Make wire connections (connectors not provided.) Reference

chart below for correct connections and wire accordingly.

5) Push ﬁxture to wall, carefully passing mounting screws

through holes.

6) Secure ﬁxture to wall using threaded balls.

7) Raise glass up to ﬁxture. Fit glass inside cage and pass hole

in glass over socket.

8) Raise bottom cap up to ﬁxture. Fit bottom cap onto bottom of

cage.

9) From inside cage, thread screws down into holes in cage and

into bottom cap. Tighten screws to secure bottom cap to

ﬁxture.

INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS AND/

OR IN WET LOCATIONS.

10) Mounting surface should be clean, dry, ﬂat and 1/4” larger

that the canopy on all sides. Any gaps between the mounting

surface and canopy exceeding 3/16” should be corrected as

required.

11) With silicone caulking compound, caulk completely around

where back of canopy meets the wall surface to prevent

water from seeping into outlet box.

Connect Black or

Red Supply Wire to:

Connect

White Supply Wire to:

Black White

*Parallel cord (round & smooth) *Parallel cord (square & ridged)

Clear, Brown, Gold or Black

without tracer

Clear, Brown, Gold or Black

with tracer

Insulated wire (other than green)

with copper conductor

Insulated wire (other than green)

with silver conductor

*Note: When parallel wires (SPT I & SPT II)

are used. The neutral wire is square shaped

or ridged and the other wire will be round in

shape or smooth (see illus.)

Neutral Wire

Date Issued: 7/20/12 IS-49339-CB

MOUNTING STRAP

BARRETTE DE MONTAGE

INSTRUCTIONS

For Assembling and Installing Fixtures in Canada

Pour L’assemblage et L’installation Au Canada

THREADED BALL

BOULE FILETÉ

GLASS

VERRE

SCREW

VIS

BOTTOM CAP

CAPUCHON INFÉRIEUR

BOTTOM CAP

CAPUCHON INFÉRIEUR

GLASS

VERRE

CAGE

SEE OTHER SIDE FOR CANADIAN FRENCH TRANS-

LATIONS.

VOIR L’AUTRE CÔTÉ POUR LES CANADIENS TRA-

DUCTIONS EN FRANÇAIS.

1 2

LATIONS 1
DUCTIONS EN FRANÇAIS 1

Résumé du contenu

Page 1 - DUCTIONS EN FRANÇAIS

1) TURN OFF POWER. IMPORTANT: Before you start, NEVER attempt any work without shutting off the electricity until the work is done. a) Go to t

Page 2

1) COUPER L’ALIMENTATION SECTEUR. IMPORTANT: TOUJOURS couper l’électricité avant de commencer le travail. a) Localiser le coffret à fusibles

Commentaires sur ces manuels

Pas de commentaire

Kichler 49339 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Éclairage Kichler 49339. Kichler 49339 Manuel d'utilisation Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Éclairage Kichler 49339